#60010; Fume Trap™ Fume Absorber; $56.00

The Fume Trap™ provides a safer working environment by drawing fumes away and then traps them in a disposable activated carbon filter.

Key Features

• A 110 CFM, axial type fan provides maximum fume intake up to 12-14" away. CFM is Cubic Feet Per Minute and measures the volume of air replaced each minute by the fan.
• The disposable activated carbon filter cartridge "snaps" into the rear of the housing and is easy to install or remove. Replacement filters are sold three to a pack.
• A top mounted handle and four non skid rubber feet make it very portable. The fixed front grill protects the user from the fan without restricting air flow.
• A 6 ft power cord provides plenty of reach. An in-line on/off switch makes it easy to operate.

Many alternate voltages and or plug configurations are available for this product at no additional cost, please see this chart for those available choices and the corresponding product order number.

110 CFM (Cubic Feet / Minute of air moved)
1 Amp Draw
Construction: Stamped steel housing.
Color: Gray fleck body with plastic handle.
Size: 5" wide x 5" high x 6" deep.

Available Parts and Accessories

• Stock No. 60006: 3-Pk Replacement Filters

#50110; Dop Station™; $35.00

A thermostatically-controlled ceramic heater for melting and keeping your dop wax at the perfect temperature along with built in storage for all your tools!

Key Features

• Handy storage for dop sticks, wax, and other tools.
• Lighted switch for convenient and safe operation.
• Wide bezel on warming pot for pre-heating stones.
• Use for melting waxes for dopping cabochons (with green wax) or faceting rough (with black wax)
• Pre-heat stones on the wide bezel for better adhesion (Note: some temperature resistant stones should be warmed with care.)

115V / 60Hz

Available Parts and Accessories

• Inland no. 4501000: Dop Wax - 1/4 lb.

#50072; Slim Line™ Carbide Wheel Cutter; $24.00

Save time and effort in cutting your pre-form cabs with this high quality cutter. Designed to score glass, these long lasting carbide wheel cutters will also enable you to score and break preform shapes out of thin cut slabs of agate and other minerals. You'll be amazed at how often you can use these in place of the trim saw! Though these cutters can be used with a cutting oil, it is not required for lapidary work.

Key Features

• Heads, axles and wheels are highest quality tungsten carbide steel.

• Cutting wheel designed to hold its edge longer.

• Close construction tolerances for smooth rolling wheels with no chatter. 

• The slimmer body is most like holding a pencil or pen.

• Lightweight, slightly textured acrylic barrel makes it easy to hold

Comes with standard narrow cutter head

Available Parts and Accessories

• Inland no. 50090: Narrow replacement cutting head

• Inland no. 50091: Wide replacement cutting head

  ---

#76020; Magna Light™ Lighted Magnifier; $46.00

Magna Light™ is an ideal light and magnifier for shaping, sawing, drawing or working with small items or intricate details.

Key Features

• Includes two adjustable mounting clamps that attach to any horizontal or vertical surface up to 2" in thickness.
• Two mounting clamps so it can be moved quickly from one area to another without having to reinstall a clamp.
• Uses a single standard light bulb (not included) up to 60 watts maximum.
• UL listed and operates off a standard 110V electrical outlet.
• Sturdy spring tensioned jointed metal arm.
• The head (containing the light source) has a swing away, 3 1/2" precision ground optical magnifier.
• Revolves a full 360º .
• The head can be adjusted to a maximum vertical height of 16" above the mounting surface and rotates in a ball joint to an infinite number of positions.
• One Year Warranty.

Metal arm with a molded plastic head housing the socket.
Optical quality magnifying lens.
Clamps are molded plastic with threaded metal bar and nut.
One Year Warranty

#350078; Pistol Type Carbide Wheel Cutter; $30.00

Save time and effort in cutting your pre-form cabs with this high quality cutter. Designed to score glass, these long lasting carbide wheel cutters will also enable you to score and break preform shapes out of thin cut slabs of agate and other minerals. You'll be amazed at how often you can use these in place of the trim saw! Though these cutters can be used with a cutting oil, it is not required for lapidary work.

Key Features

• Heads, axles and wheels are highest quality tungsten carbide steel.
• Cutting wheel designed to hold its edge longer.
• Close construction tolerances for smooth rolling wheels with no chatter.
• Easy to hold pistol type grip. The hand wraps entirely around the handle and ensures correct positioning of the cuter head and requires less pressure to make a good score.

Comes with standard narrow cutter head

Available Parts and Accessories

• Inland no. 50090: Narrow replacement cutting head

• Inland no. 50091: Wide replacement cutting head

#50074; Brass Barrel Carbide Wheel Cutter; $28.00

Save time and effort in cutting your pre-form cabs with this high quality cutter. Designed to score glass, these long lasting carbide wheel cutters will also enable you to score and break preform shapes out of thin cut slabs of agate and other minerals. You'll be amazed at how often you can use these in place of the trim saw! Though these cutters can be used with a cutting oil, it is not required for lapidary work.

Key Features

• Heads, axles and wheels are highest quality tungsten carbide steel.

• Cutting wheel designed to hold its edge longer.

• Close construction tolerances for smooth rolling wheels with no chatter. 

• Brass barrel gives this cutter a heavier weight and feel of stability.

• The textured barrel makes it easier to grip and steer

Comes with standard narrow cutter head

Available Parts and Accessories

• Inland no. 50090: Narrow replacement cutting head

• Inland no. 50091: Wide replacement cutting head

  ---

#50076; Heavy Duty Carbide Wheel Cutter; $24.00

Save time and effort in cutting your pre-form cabs with this high quality cutter. Designed to score glass, these long lasting carbide wheel cutters will also enable you to score and break preform shapes out of thin cut slabs of agate and other minerals. You'll be amazed at how often you can use these in place of the trim saw! Though these cutters can be used with a cutting oil, it is not required for lapidary work.

Key Features

• Heads, axles and wheels are highest quality tungsten carbide steel.

• Cutting wheel designed to hold its edge longer.

• Close construction tolerances for smooth rolling wheels with no chatter.

• Pencil style handle has concentric ridge rings on the acrylic barrel help provide a sure grip,

Comes with standard narrow cutter head

Available Parts and Accessories

• Inland no. 50090: Narrow replacement cutting head

• Inland no. 50091: Wide replacement cutting head

#50019; Flex Shaft™ Accessory; $37.00

The Flex Shaft™ turns your SwapTop™ motor into a hand held engraving, drilling, and shaping tool.

Key Features

• The Flex Shaft™ accessory fits onto all motors with a 5/16" diameter shaft. Simply plug it on and it's ready to go.
• The Flex Shaft™ works with nearly any 1/32" to 1/8" shaft tool or bit
• Use it to engrave, polish, sand, drill, and create intricate detailing in many materials.
• Use with our Diamond Carving Tip Sets to carve, shape and engrave stone, marble, tile, glass, and other mineral based materials.
• The drill style chuck is easy to use.

Fits most machines with a standard 5/16" motor shaft
Works with 1/32" to 1/8" diameter shaft tools.
Length: 42" (106 cm)

Available Parts and Accessories

• 50 Pc Diamond Carving Tip Set: For engraving, carving, and shaping stone, plastics, and more.

• 20 Pc Diamond Carving Tip Set: For engraving, carving, and shaping stone, plastics, and more.

• 10 Pc Diamond Carving Tip Set: For engraving, carving, and shaping stone, plastics, and more.

#50105; Easy Mark™ Electric Engraver; $29.00

50115; 20 Pc. Diamond Carving Tip Set; $20.00

This set contains twenty tips to carve, engrave on, and shape stone, plastics and more. Use with the FlexShaft™ and EasyMark™ Engraver to create custom designs, add detail, sign your work, and even identify your valuables.

Key Features:

• Includes 20 of the most popular types of carving tips:
  • 8 Randomly Sized Cylinder/Cone Combinations
  • 3 Assorted Cylinder Tips
  • 3 Assorted Ball Tips
  • 3 Assorted Cone Tips
  • 1 Flat Head "Disk" Tip
  • 1 "Christmas Tree" Tip
  • 1 Tear Drop Tip
• All tips are diamond plated for long lasting use.
• Tips come in a handy self storing case to keep them neat and orderly.
• Use with Inland EasyMark™ Electric Engraver, FlexShaft Accessory with SwapTop™ Machines.

Shaft diameter: 2.32mm OD
20 tips in a self closing blue plastic case

The Easy Mark™ is a lightweight power tool for carving and engraving on stone, marble, glass, plastics and more. Use it to create custom designs, add detail, sign your work, and even identify your valuables.

Key Features

• The Easy Mark™ Electric Engraver is light weight, comfortable to hold and easy to control.
• It is UL approved, with an 18,000 RPM high speed 12 volt motor.
• Comes complete with a removable diamond small ball tip.
• Additional diamond tips are available (see our 20 pc. Carving Tip Set) to create different effects.
• Tips are very easy to change. Simply pull out the old one and press in the new one.

Easy Mark is available in alternate voltages and or plug configurations at no additional cost, please see this chart for those available choices and the corresponding product order number

Construction: Lightweight impact resistant plastic.
Size: 6" x 3.5"
UL approved
18,000 RPM high speed 12 volt motor.

Additional Parts and Accessories

• 20 Pc Diamond Carving Tip Set: For engraving, carving, and shaping stone, plastics, and more.
• 4 pc Bead Reamer Set: This set is designed specifically to clean out, enlarge, and finish off the holes created when making beads.